Aim MXG Car Racing Dash Dashboard Data logger with 50cm GPS Module. 0% Interest Free finance Available! The Aim MXG Car Dash Data logger from Aim designed to acquire and display data from your car ECU. Racing data is also acquired from the internal accelerometer, gyro as well as from the GPS Module included in the kit. Performance and data acquired can also be incremented adding up to eight expansion modules.MXG A Wide Range of Data Sources. Aim MXG is the new dash logger designed to acquire and display data coming from your engine ECU, the internal accelerometer, gyro, and from the GPS Module included in the kit. Analog/digital inputs and predefined math channels. The only difference between the two is the MXS is a compact 5 display and MXG is a 7 display, a better fit for wide cockpit installations. Aim MXG acquires data from the ECU of your vehicle. The list of available ECU drivers is constantly updated and upgraded and is published in our support site which include over 1000 different ECUs, either Stock and Racing. From a hardware point of view, MXG manages the following data lines. MXG has eight analog inputs, recorded up to 1000 times per second each. You can connect and monitor all kinds of sensors, like. K-type thermocouple and many others, all your custom sensors includ. MXG also features six digital inputs. Four speed signals MXG can receive the speed signal from the ECU, from the GPS and from the four wheel sensors. RPM MXG can receive the RPM signal from the ECU or from a digital input connected to a square wave signal (8 to 50 V) or to a low voltage (from 150 to 400 V) of the coil. Lap signal Lap and split times are sampled by the GPS (included in the kit) or via optical receiver/transmitter. The GPS08 Module (included in the kit) connected via CAN to the MXG makes lap time calculation and track position analysis very easy. Each Aim MXG memory stores more than 200 world tracks start/finish line coordinates: as soon as Aim MXG is switched on, the GPS08 Module will locate its position, identify track-line coordinates and start immediately sampling lap and split time. If the track is not included in the database, it is always possible to add the start/finish line coordinates to the Aim MXS via PC before going to the track, using the Race Studio 3 Track Manager software. An innovative MXG feature is its CAN2 line, managing data coming from your additional modules i. ABS, traction control, infrared temperature sensors and more. This feature meets the requirements of a growing number of racers, as the use of additional modules is becoming quite common in a number of series. MXG Internal Accelerometer and Gyro. The internal three-axial accelerometer and the gyroscope provide the MXG a very powerful array of information. These force and motion sensors enable you to quantify the dynamic characteristics of your vehicle. Measuring acceleration forces and gyro rates can assist in determining how to improve your vehicle performances.
With MXG you immediately get Math Channels values. The dash logger can be configured to display those values i. Brake bias, calculated gear in real time. Extra Wide, High Contrast 7 TFT display.The MXG display features a high contrast 7 TFT display, fully configurable by a dedicated software. An ambient light sensor keeps the backlight at optimum brightness levels. You can define all the custom pages you wish, choosing among a wide library of page styles, defining which data to be shown, their end of scale and measure units. Swapping between pages can be managed pushing one or two push buttons. MXG has Eight configurable RGB alarm LEDs.
You choose the conditions, you choose the colours. Select a solid alarm or flashing one and the flashing frequency then choose to have an accompanying text message and set the alarm priorities. Aim MXG features two digital outputs.
Each of them can give an output of 1 amp at 12 volts: they can be configured in order to be turned on/off depending on the value of the analogue or digital inputs. They permit to automatically run external systems, i.
To switch on/off additional lights, to activate/de-activate a cooling fan or circulation pumps, etc. When a certain event happens. Choose from a host of advanced multicoloured RGB shift light patterns that can be customised to your liking, and for each unique gear when required.Using the built-in CAN bus, you can add expansion modules to the Aim MXG to increment the performance and the data acquired. Race Studio 3 is the heart of your MXG managing all your racing activities. The Race Studio 3 can create, modify, delete, import and export configurations with all channels, ECU drivers, Math channels, Display Pages, Digital outputs, Alarms, Shift Lights and all the expansions you need. You will also be able to manage the map of all your racing tracks and compare two laps watching the video recorded by SmartyCam HD cameras. 700cd/m2 - 1,100 Lumen Ambient light sensor.
8 RGB freely configurable Shift lights. 10 integrated freely configurable RGB LEDs CAN connections. CAN, RS232 or K-Line ECU compatibility. + 1,000 industry leading ECUs Expansion CAN connection. GPS, Channel Expansion, Thermocouple Expansions, Lambda Controller.
8 fully configurable, max 1,000 Hz each Digital inputs. 4 Speed inputs, lap signal, coil RPM input Digital outputs. 2 (1 Amp max each) Second CAN. Internal Three-axial ± 5G + Three-axial Gyroscope Internal memory. MXG Dash Datalogger for Car Racing.
50cm GPS Module with cable. Any Items That Are Out Of Stock Or have Extended Lead Times, May Take Slightly Longer Than Normal.
The item "Aim MXG Car Racing 7 TFT Dash Dashboard Data logger with 50cm GPS Module" is in sale since Thursday, April 9, 2020. This item is in the category "Vehicle Parts & Accessories\Garage Equipment & Tools\Other Garage Equipment & Tools". The seller is "shopbhp" and is located in Sevenoaks, Kent. This item can be shipped worldwide.